Battle Tanks Nederland

BTN is de club voor 1:16 en 1:15 RC BATTLE SYSTEM tankliefhebbers
Het is nu 29 maart 2024, 06:15

Alle tijden zijn GMT + 1 uur




Plaats een nieuw onderwerp Antwoord op onderwerp  [ 8 berichten ] 
Auteur Bericht
BerichtGeplaatst: 13 mei 2014, 17:47 
Hi all,

Ralf has m as I recently brought up with an idea to provide the 3:1 steel gears with a cover.
So I sat down in the evening when I was in the business time and a little drawn.

Afbeelding

And so the prototypes are already in print.

Afbeelding

Tomorrow I can see ma exactly how they fit and if necessary adjust anything else.


Omhoog
  
 
BerichtGeplaatst: 14 mei 2014, 17:22 
I'm still not happy with it.

This is the second option and I have to adjust the cap in a few places and around the drive wheel a little better.

Afbeelding

Afbeelding

Afbeelding

Afbeelding

In the third variant, I just draw and this fits most then.


Omhoog
  
 
BerichtGeplaatst: 15 mei 2014, 16:00 
Today coming from the printer early covers are now almost usable.

Afbeelding

Afbeelding

Afbeelding

Afbeelding

I've made ​​a few small changes to cover also the last gap and better gestallten especially the enclosure of the drive shaft, but that should be it now.

So the first four pairs are now in print.

Afbeelding

However, there will be such that one on the drive axle to the tub for installation and something has to adapt depending on space and reinforced the covers. Depending on how much space is available in each tank.

And today I have taken the time Asiatam flat gear into the business.
Time seeing how I as a full coverage approaches, and bring a few Tamiya gear I have are still here.


Omhoog
  
 
BerichtGeplaatst: 16 mei 2014, 15:49 
Now the covers are done constructively .

Just as she now has to come out of the printer you but first remove the support Struck doors, which is not so difficult but .
To do this simply pushes a knife or a thin screwdriver under it and levering it on the sides , piece by piece from . The PLA used then breaks off brittle.

Afbeelding

Afbeelding

And so do the insides without these supporting structures.

Afbeelding

If you then have the space in the tank , you can simply back the covers , like start in this picture and simply clip it with a little caution to the front.

Afbeelding

Unfortunately, it will not be when the transmission queue directly on the front possible in all Hull. Since one must then match the best cut off the front, with a small blade.

And this is what the covers then the transmissions from now .

Afbeelding

Afbeelding

And here I have put them in a KV- bath times.

Afbeelding


Omhoog
  
 
BerichtGeplaatst: 18 mei 2014, 09:36 
Yesterday I casually sometimes drawn a first prototype for a cover of the Asiatam flat gear.

Afbeelding

Since both of these pair of gears are the same, but mirrored and I just have to adjust a print first. If this fits then simply reflect the drawing and I have two matching covers.

Let's see if I can still print the prototypes evening today?


Omhoog
  
 
BerichtGeplaatst: 19 mei 2014, 18:43 
Today, the first prototype was ready now.

Afbeelding

Afbeelding

When I tried but I had to then determine the fit, it was probably been but a bit late and a long day as I drew the .....

Afbeelding

Afbeelding

But never mind, because the first component anyway never true. So improved and currently has been running the printing of the second prototype.


Omhoog
  
 
BerichtGeplaatst: 20 mei 2014, 14:50 
Today I was able to try out the new cover on the flat gear.

That now looks much better.

Afbeelding

Afbeelding

Some small changes and even then it might fit.


Omhoog
  
 
BerichtGeplaatst: 21 mei 2014, 16:46 
The final pressure was now almost usable.

Afbeelding

Afbeelding

What I had to adjust I made and now run 6 covers on the printer overnight.

Afbeelding


Omhoog
  
 
Geef de vorige berichten weer:  Sorteer op  
Plaats een nieuw onderwerp Antwoord op onderwerp  [ 8 berichten ] 

Alle tijden zijn GMT + 1 uur


Wie is er online

Gebruikers op dit forum: Geen geregistreerde gebruikers en 1 gast


Je mag geen nieuwe onderwerpen in dit forum plaatsen
Je mag niet antwoorden op een onderwerp in dit forum
Je mag je berichten in dit forum niet wijzigen
Je mag je berichten niet uit dit forum verwijderen

Ga naar:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB.nl Vertaling